Red Clay Bricks (Sengal): Price per 1,000 and per Load

Red brick price per piece, per 1,000 and per load

Chennai quotes for red clay bricks in mid-2026 ran from about ₹8 to ₹16 a brick (₹8,000–16,000 per 1,000). The spread comes from type (chamber or wire-cut), size and whether delivery is included.

Next question: How do I know a load is good? Colour, ring, fracture, soak and salt: six checks next. More

Six checks for a load of red bricks

1. Colour: an even, deep red-brown; pale, yellowish bricks are under-burnt, and very dark or warped ones over-burnt.
2. Ring test: two bricks struck together should ring, not thud.
3. Break one: the inside should be even, with no lime lumps, pebbles or cracks.
4. Soak one for 24 hours: it should not gain more than 20% of its dry weight (IS 1077 limit for classes up to 12.5).
5. Let the soaked brick dry and look for white salt patches; heavy patches (efflorescence) come through plaster later.
6. Lay ten bricks end to end against ten more from another part of the load; hand-moulded bricks vary, but the rows should match closely.

Next question: What is a chamber brick? A clay brick fired in a chamber kiln; the definition follows. More

What red clay and chamber bricks are

Red clay bricks are moulded from clay and fired in a kiln, which gives the colour and the hardness. Tamil Nadu calls them sengal; chamber bricks are fired in a chamber kiln, while wire-cut bricks are machine-extruded and cut, with sharper edges.

IS 1077 is the standard for common burnt clay bricks. It sets strength classes from 3.5 N/mm² upward and limits water absorption and efflorescence.

Next question: Which limits matter on site? Absorption and efflorescence; see the table. More

IS 1077 limits that matter on site

The standard's modular size is 190 x 90 x 90 mm; the trade in Chennai mostly sells the larger non-modular brick of about 9 x 4 x 3 inch.

Next question: How many bricks for my wall? About 900 per 100 sq ft of 9-inch wall (typical). More

How many red bricks do you need? Typical estimates

Typical estimates: with 10 mm joints; deduct openings and add about 5% for breakage.

Next question: What does that cost delivered? Multiply by the per-1,000 price and add the delivered load price for your area. More

Chamber, wire-cut or fly ash?

• Chamber bricks: plastered walls and load-bearing brickwork on a budget.
• Wire-cut bricks: exposed brickwork and sharp edges, at a higher price; ask for a quote.
• Fly ash bricks: even faces and less plaster on framed houses.
• Solid blocks: fewer pieces and faster laying for infill and compound walls.

Next question: How do I store bricks? Stack on edge and soak before laying. More

Storing and soaking red bricks

• Unload by hand and stack on edge on firm, level ground, no higher than about 1.5 m.
• Soak clay bricks in water for a few hours before laying, so they do not draw water out of the mortar.
• Keep them clear of soil and standing water; salts from the ground feed efflorescence.
• Use broken bricks as hardcore, not in the wall.

Next question: What goes wrong most often? Over- and under-burnt bricks and short counts. More

Mistakes to avoid with red bricks

• Taking pale, under-burnt bricks because the price is low; they absorb water and crumble.
• Laying dry bricks; the mortar loses water and bonds poorly.
• Guessing the count on the lorry by eye instead of counting a few rows and multiplying.
• Using bricks with heavy salt patches in walls that stay damp.

Next question: Would fly ash bricks suit a plastered wall better? Often, yes; compare prices and faces. More

Red Clay Bricks: delivered price by area

Delivered price per 1,000 = yard price + freight on about 3 t from the nearest yard or the Gummidipoondi SIPCOT factories, assuming a full lorry; before GST.

Next question: how much do I need? Quantity calculator · Delivered-cost estimator

How to order red bricks

1. Send the count (or the wall area) and your site location on WhatsApp, by phone or through the quote form.
2. We confirm the price per 1,000, the nearest yard and the delivered price per load.
3. Run the colour, ring and soak checks on the first load before unloading it all.